DIN 19246-1991 测量和控制.项目程序.术语及定义

上一篇: DIN 5007-1991 字母排列顺序规则(ABC规则)
下一篇: DIN EN 29592-1-1991 信息处理系统.计算机绘图.程序员分级交互图形系统.第1部分:功能描述

Product Code:SAE J2517
Title:Hybrid III Family Chest Potentiometer Calibration Procedure
Issuing Committee:Dummy Testing And Equipment Committee
Scope:This procedure establishes a recommended practice for establishing the sensitivity of the chest displacement potentiometer assembly used in the Hybrid III family of Anthropomorphic Test Devices (ATDs, or crash dummies). This potentiometer assembly is used in the Hybrid III family to measure the linear displacement of the sternum relative to the spine (referred to as chest compression). An inherent non-linearity exists in this measurement because a rotary potentiometer is being used to measure a generally linear displacement. As the chest cavity is compressed the potentiometer rotates, however the relationship between the compression and the potentiometer rotation (and voltage output) is non-linear. Crash testing facilities have in the past used a variety of techniques to calibrate the chest potentiometer, that is to establish a sensitivity value (mm/(volt/volt) or mm/(mvolt/volt)). These sensitivity values are used to convert recorded voltage measurements to engineering units, in this case chest compression in mm. Some of these techniques intended to correct for the non-linearity and others did not. Of those that did correct for the non-linearity, there was a variation in techniques used. This variation in calibration procedures was in part identified by the SAE Dummy Testing Equipment Subcommittee (DTES), and led to overall variability in chest compression measurements between laboratories. The intent of this SAE Recommended Practice is to minimize the variations in chest deflection measurements between crash testing laboratories. Before this procedure was written, a round robin showed variations for the Small Female of 10% among 8 labs for the chest pot sensitivity value. A follow-up round robin to test this procedure showed a worst case variation of 2.7% among 10 labs, with a standard deviation of 0.9%. The calibration procedure recommended here uses a two-point calibration and is not intended to correct for the non-linearity (which, for example, is as large as 3% for the Small Female but is small near the peak). It also does not require the measurement of a starting position of the potentiometer before each crash test, thus it does not correct for the difference in starting chest geometry between a subject dummy and its design intent. It is intended to be a simple and reproducible calibration procedure which crash test facilities can easily adopt with little or no modifications to their facilities. More complex procedures could in fact address the non-linearity, but at the likely cost of non-adoption by some facilities.【英文标准名称】:SafetyaspectsforxDSLsignalsoncircuitsconnectedtotelecommunicationnetworks(DSL:DigitalSubscriberLine)
【原文标准名称】:连接通信网络的电路的xDSL信号的安全情况
【标准号】:IEC/TS62367-2004
【标准状态】:现行
【国别】:国际
【发布日期】:2004-01
【实施或试行日期】:
【发布单位】:国际电工委员会(IEC)
【起草单位】:IEC/TC108
【标准类型】:()
【标准水平】:()
【中文主题词】:信号传输;连接线;通信;电子设备;电信网;通信传输线路;公众交换电话网;电信;用户台;用户专用线路;数字信号;通信网;安全;电路网络;信息交换;综合服务数字网络
【英文主题词】:
【摘要】:ThistechnicalspecificationaddressesthesafetyimplicationsofhavingxDSLsignalsoncircuitsinequipmentconnectedtoaTELECOMMUNICATIONNETWORK,andgivesrulesfordealingwithsuchequipmentinthecontextoftheIEC60950series.
【中国标准分类号】:M11
【国际标准分类号】:33_040_40
【页数】:20P;A4
【正文语种】:英语